Gibbons, Gregory John, 1970-, Segui-Garza, Juan Jose and Hansell, Robert George. (2010) Variable cavity volume tooling for high-performance resin infusion moulding. Institution of Mechanical Engineers. Proceedings. Part G: Journal of Aerospace Engineering, Vol.224 (No.4). pp. 499-509. ISSN 0954-4100

PDF WRAP_gibbons_Variable_cavity.pdf - Requires a PDF viewer such as GSview, Xpdf or Adobe Acrobat Reader Download (508Kb)

Abstract

This article describes the research carried out by Warwick under the BAE Systems/EPSRC programme ‘Flapless Aerial Vehicles Integrated Interdisciplinary Research – FLAVIIR’. Warwick's aim in FLAVIIR was to develop low-cost innovative tooling technologies to enable the affordable manufacture of complex composite aerospace structures and to help realize the aim of the Grand Challenge of maintenance-free, low-cost unmanned aerial vehicle manufacture. This article focuses on the evaluation of a novel tooling process (variable cavity tooling) to enable the complete infusion of resin throughout non-crimp fabric within a mould cavity under low (0.1 MPa) injection pressure. The contribution of the primary processing parameters to the mechanical properties of a carbon composite component (bulk-head lug section), and the interactions between parameters, was determined. The initial mould gap (di) was identified as having the most significant effect on all measured mechanical properties, but complex interactions between di, n (number of fabric layers), and vc (mould closure rate) were observed. The process capability was low due to the manual processing, but was improved through process optimization, and delivered properties comparable to high-pressure resin transfer moulding.

Item Type:	Journal Article
Subjects:	T Technology > TS Manufactures T Technology > TJ Mechanical engineering and machinery
Divisions:	Faculty of Science > WMG (Formerly the Warwick Manufacturing Group)
Library of Congress Subject Headings (LCSH):	Machining, Gums and resins, Carbon fibers, High technology, Aerospace engineering
Journal or Publication Title:	Institution of Mechanical Engineers. Proceedings. Part G: Journal of Aerospace Engineering
Publisher:	Sage Publications Ltd.
ISSN:	0954-4100
Date:	1 April 2010
Volume:	Vol.224
Number:	No.4
Number of Pages:	11
Page Range:	pp. 499-509
Identification Number:	10.1243/09544100JAERO582
Status:	Peer Reviewed
Publication Status:	Published
Access rights to Published version:	Open Access
Funder:	Engineering and Physical Sciences Research Council (EPSRC), BAE SYSTEMS (Firm)
Grant number:	FLAVIIR (EPSRC), WIMRC (EPSRC)
References:	1 Achim, V., Soukane, S., Trochu, F., and Bréard, J. Optimization of injection flow rate to minimize micro/ macro-voids formation in resin transfer molded composites. Compos. Sci. Technol., 2006, 66(3–4), 475–486. 2 Bowles, K. J. and Frimpong, S. Void effects on the interlaminar shear strength of unidirectional graphitefiber- reinforced composites. J. Compos. Mater., 1992, 26(10), 1487–1509. 3 Armstrong, D. L., Goodwin, S. L., Sharpless, G., Hethcock, J. D., Andrews, J., and Coyle, L. Development of a low-cost integrated RTM horizontal stabilizer that flies on Bell Helicopter’s MAPL. SAMPE J., 2006, 42(3), 54–62. 4 Sutton, G. Affordable RTM aerospace components. SAMPE J., 1999, 35(3), 58–63. 5 Cochran, R., Matson, C., Thoman, S., and Wong, D. Advanced composite processes for aerospace applications. In Proceedings of the International SAMPE Symposium and Exhibition on Evolving Technologies for the Competitive Edge, Anaheim, California, USA, 1997, vol. 42, no.1, pp. 635–640. 6 Toi, Y., Harada, A., Tanaka, S., Amaoka, K., and Kikukawa, H. Development of affordable composite wing structure. Adv. Compos. Mater.: Off. J. Jpn. Soc. Compos.Mater., 2004, 12(4), 321–329. 7 Backhouse, R. Mercedes Benz SLR McLaren – a step towards affordable CFRP structures. In Proceedings of the Sixth Annual SPE Automotive Composites Conference, Detroit,Michigan, USA, 2006, p. 859. 8 Grande, J. One step to processed auto parts. Mod. Plast. Int., 1995, 25(5), 52. 9 Cairns, D. S. and Skramstad, J. D. Evaluation of hand lay-up and resin transfer molding in composite wind turbine blade structures. In Proceedings of the International SAMPE Symposium and Exhibition, Long Beach, California, USA, 2000, vol. 45, no. I, pp. 967–980. 10 Ikegawa, N., Hamada, H., and Maekawa, Z. Effect of compression process on void behavior in structural resin transfer molding.Polym.Engng Sci., 1996, 36(7), 953–962. 11 Choi, J. H. and Dharan, C. K. H. Enhancement of resin transfer molding using articulated tooling. Polym. Compos., 2002, 23(4), 674–681. 12 McConnell, V. P. Advanced RTM produces complex, repeatable, flight-critical parts. SAMPE J., 1998, 34(6), 37–43. 13 Shojaei, A. Numerical simulation of three-dimensional flow and analysis of filling process in compression resin transfer moulding. Compos. Part A, Appl. Sci. Manuf., 2006, 37(9), 1434–1450. 14 Plessinger, J., Myers, J., Brachos, V., and Rossi, G. Development of a sequential multiport resin injection manifold system (SMRIMS) to RTM a 16 ft structural car chassis. In Proceedings of the InternationalSAMPETechnical Conference, Covina, California, USA, 1998, vol. 30, pp. 361–372. 15 Babu, B. J. C., Prabhakaran, R. T. D., and Agrawal, V. P. Quality evaluation of resin transfer molded products. J. Reinf. Plast. Compos., 2008, 27(6), 559–581. 16 Seeman,W. H. Plastic transfer molding techniques for the production of fiber reinforced plastic structures.US Patent 4902215, 1990. 17 Brouwer,W. D.,Van Herpt, E. C. F. C., and Labordus, M. Vacuum injection moulding for large structural applications. Compos. Part A, Appl. Sci. Manuf., 2003, 34(6), 551–558. 18 Sewell, T. A., Wanthal, S., and Rapp, R. Improved laminate physical and mechanical properties using ‘hytest’ vacuum assisted resin transfer molding. In Proceedings of the International SAMPE Symposium and Exhibition, Long Beach, California, USA, 2005, vol. 50, pp. 1271–1287. 19 British Standards Institute. Plastics – determination of tensile properties. Part 4: test conditions for isotropic and orthotropic fibre-reinforced plastic composites. BS EN ISO 527-4,1997. 20 British Standards Institute. Fibre-reinforced plastic composites – determination of flexural properties. BS ENISO 14125,1998. 21 Montgomery, D. Introduction to statistical quality control, 2005, p. 776 (JohnWiley, New York). 22 Mills, A. AMICC project laminate characterisation. Internal AMICC Project Report, Centre for Lightweight Composites, Cranfield University, 2001. 23 Anon. RTM 120/HY2954. 120C Epoxy System for RTM Product Data Sheet. Hexcel Composites ITA 086, 1998. 24 Fujita, A., Hamada, H., and Maekawa, Z. Tensile properties of carbon fibre triaxial woven fabric composites. J. Compos.Mater., 1993, 1428–1442. 25 Schwartz, M. M. Composite materials handbook, 1992 (McGraw-Hill, London). 26 de Paiva, J. M. F., Mayer, S., and Rezende, M. C. Comparison of tensile strength of different carbon fabric reinforced epoxy composites. Mater. Res., 2006, 9(1), 83–89. 27 Chowdhury,F. H.,Hosur,M.V., and Jeelani, S. Studies on the flexural and thermomechanical properties of woven carbon/nanoclay-epoxy laminates.Mater. Sci.Eng., 1989, 421(1–2), 298–306. 28 Tarpani, J. R., Milan, M. T., Spinelli, D., and Bose,W. V. Mechanical performance of carbon-epoxy laminates. Part I: quasi-static and impact bending properties.Mater. Res., 2006, 9(2), 115–120. 29 Papargyris, D. A., Day, R. J., Nesbitt, A., and Bakavos, B. Comparison of the mechanical and physical properties of a carbon fibre epoxy composite manufactured by resin transfer moulding using conventional and microwave heating. Compos. Sci. Technol., 2008, 68, 1854–1861. 30 Davies, L. W., Day, R. J., Bond, D., Nesbitt, A., Ellis, J., and Gardon, E. Effect of cure cycle heat transfer rates on the physical and mechanical properties of an epoxy matrix composite. Compos. Sci. Technol., 2007, 67, 1892–1899. 31 Hunt, W., and Skillingberg, M. Specialized aluminium products for toolandmoldapplications.AluminumNow, 2004,May/June, 23–24. 32 Gibbons, G. J., Hansell, R. G., Thacker, G., and Arnett, G. State of the art in low-cost, rapid composite forming tooling technologies. J. Adv. Mater., 2009, 41(2), 5–19.
URI:	http://wrap.warwick.ac.uk/id/eprint/3382

Data sourced from Thomson Reuters' Web of Knowledge

Request changes to a record

Actions (login required)

View Item